Dikey delik Mills (incld VTL)BULLARD 42" CUT MASTER
Texas, Birleşik Devletlergenel bakış
Marka
model
kimlik numarası
539808
Durum
Kullanılmış - İyi
Yıl
1945
seri numarası
24197
Yer
Texas
Birleşik Devletler
Birleşik Devletler
Stok #
B6006118
42" Used Bullard (Cut Master) Vertical Turret Lathe Model 42 Floor Shift Model
Metrik Özellikleri dönüştürme
Tabla Çapı | 42" |
Salınım | 46" |
Work Ht-U/R | 37" |
Güç | 30 hp |
RPM (Dönüş Sayısı/Dakika) | 150 RPM |
Ölçüler | R-L 105" X F-B 118" X 10'2" High |
Ağırlk | 42,500 Lbs. |
İle donatılmış
Note: Reconditioning:
Machine Has Been Cleaned, Painted And Cycled.
1. Turret Slide & Swivel in our facility. Dismantle unit as required. Clean all component parts.
2. Remachine all bearing surfaces of the Turret Slide to remove localized wear.
3. Remachine all bearing surfaces of the Turret Swivel to accept Turcite Way material.
4. Install Turcite to the Swivel and machine to correct height to compensate for material removed from Turret Slide.
5. Machine or grind oil grooves into swivel material for proper delivery of lubrication oil.
6. Block and hook frost all bearing surfaces of the turret slide for "pockets" for retention of lubrication oil.
7. Precision scrape and fit turret slide to swivel for proper bearing fit.
8. Manufacture new meehanite cast iron gibs for turret slide. Oil groove for proper delivery of lubrication oil. Precision scrape and fit allowing full range of adjustment to compensate for any future wear. These gibs will be the earless type.
9. Install triple lead downfeed screw and nuts. Install into nut body and realign to assure smooth and accurate operation.
10. Hang turret assembly in vertical position and reset turret locking mechanism for proper operation. Reset backlash eliminator to proper setting.
11. Cross-rail screws and nut will be replaced.
12. Turret and ram vertical screws and nuts replaced.
13. All feed and rapid shafts seals will be replaced. Hand wheel seals will be replaced, gear boxes will be cleaned and checked. Hydraulics and main motor will been reconditioned.
Machine should be ready to ship in about 16 to 20 weeks after receipt of PO.
Price will be $89,500.00 after reconditioning.
spec Sheet
Table Size..............................................42" 4-Jaw
Swing Side Head Above Table.............................45"
Swing Side Head Below Table.............................54"
Cross Rail Travel.......................................25"
Height Under Rail.......................................37"
Cross Rail Traval Up And Down...........................26"
Table Speed.............................................4.1 To 150 Rpm's
Floor To Chuck..........................................36"
Turret Head Travel Left To Right........................26-3/8"
Turret Head Swivel......................................30 Degrees
Turret Head Turret Travel Up & Down.....................30-3/8"
Max. Distance Table To Turret Face......................48-1/4"
Turret Head Position....................................5
Turret Hole Diameter....................................2-3/4"
Turret Head Feeds.......................................0.026 To 500 IPR
Side Head Travel In & Out...............................21"
Side Head Travel Up & Down..............................37"
Side Head Feeds.........................................0.026 To 500 IPR
Left Head Ram Travel Right To Left......................26-3/8"
Left Hand Ram Travel Up & Down..........................30.5"
Left Hand Ram Swivel....................................30 Degrees R To L
Left Hand Ram Tool Post Hole............................3-3/8"
Ram Head Feeds..........................................0.026 To 500 IPR
Main Motor..............................................30 Hp.
Max. Overall Height Rail and Heads In Highest Postion...145"
Machine Floor Space.....................................R-L 131.5" X F-B 104"
Machine Height..........................................9'8"
Weight..................................................42,500 Lbs.
Power Elevation Of Rail.................................Yes
Rapid Traverse To Both Head.............................Yes
Built In 4 Way Tool Post On Side Head...................Yes
Turret Head.............................................Yes
Floor Shift.............................................Yes
Condition: Good
Bu modelin daha fazla giriş gör
BULLARD 42" CUT MASTER
Dikey delik Mills (incld VTL)
BULLARD 42" CUT MASTER
Dikey delik Mills (incld VTL)
Bu Tip fazla listeleri gör
MOTCH 135
Dikey delik Mills (incld VTL)
HONOR VL-160CM
Dikey delik Mills (incld VTL)
HONOR VL-125C
Dikey delik Mills (incld VTL)
FARREL N/A
Dikey delik Mills (incld VTL)
Bu Brand daha bakın listeleri
BULLARD DYN-AU-TAPE
Dikey delik Mills (incld VTL)
BULLARD DYN-AU-TAPE
Dikey delik Mills (incld VTL)
BULLARD DYN-AU-TAPE 46
Dikey delik Mills (incld VTL)
BULLARD 46
Dikey delik Mills (incld VTL)