Гидравлические прессыMAGNUM M4PB25
СШАобзор
Марка
Модель
ИД №
612977
Состояние
Новый В-складе
Год
2024
Местонахождение
США
Складской №
12164
(1) New 25 Ton Magnum 4 Post Guided Platen Bench Model Gap Frame Hydraulic Press
Преобразование Спецификации для метрической
Ton | 25 T |
Bed L-R | 24 in |
Bed F-B | 16 in |
Stroke | 10 in |
Daylight Opening | 20 in |
Speed | 265820 ipm |
Размеры | 39” lr x 55” fb x 60” high |
Вес | 4,105# |
Оснащен
Structural Designs undergo rigorous analysis through Finite Element Analysis design testing
Allen Bradley MicroLogix PLC with Panel View HMI based controls
Hardened Precision Ground Guide Posts Single Point Power Connection
2-Hand Anti-Tie-Down Start Buttons CAT 4 Safety Start Relay
NEMA 12 enclosures NFPA-79 / UL 508A Compliant Electrical Controls
High Temp/Low Level Warning Gauge Magnetic Starter/ Electronic Overload
Lockable Disconnect Press mounted controls.
Primary power flow for press functions is handled by a CAT 4 two-hand anti-tie down safety relay. This specialty relay checks complementary inputs from each cycle initiator to insure the operators hands are out of the work area.
Top Stop Over-Run allows press to bypass top stop RAM setting in setup modes
Pressure and Distance Reversal Mode allows operator to select between pressure or position reversal
All wiring is terminated to spring cage style terminals. These terminals provide reliable vibration resistant connections. Wiring on the panel is routed through wire troughs with removable covers.
All PLC I/O points are also terminated to the terminals. Systems include multiple guard terminals already installed. Inputs and outputs have all necessary connections (power for proximity switches and grounds and neutrals for coils) on a single terminal, no searching for support wiring for devices.
All valve coils use DIN 43650 connections with power indicator lighting and electrical EMF surge suppression.
A simple, removable and easily serviceable press mounted press hydraulic system powers the press
The heart of the hydraulic system features an efficient steel manifold designed to consolidate valving, reduce plumbing, eliminate leaks, minimize pressure drop and provide maximum service life.
Efficient Screw In Cartridge Valves (SICV) solenoid valves have extremely low leakage, low pressure drops, low cost low current operation and simple maintenance. Piloted DIN logic elements outperform large piloted spool valves in leakage, flow and response time. Valve shift times are 30% of comparable piloted spool valves resulting in increased press cycle speeds.
Manifold System offers redundant safety feature which requires 3 solenoids to be energized before there can be any movement of the RAM in extend or retract. Failure of any single component will result in no hazardous motion of press RAM.
Electro-Hydraulic Decompression with FAST ACTING 3 stage decompression offering resistance to damaging decompression pressure spikes that is far superior to hydraulic or mechanical decompression used in other presses.
All final pressure connections use Flat Face O-Ring Hydraulic Connections to provide the most leak resistant hydraulic system. No metal to metal pressure connections and no pipe thread are used.
PDF manual with startup instructions, troubleshooting guide, hydraulic circuit with manufacturers part number bill of material, electrical diagram and PLC program.
18 month parts warranty against defects in workmanship
Спецификация
NOTE: 18 Months Parts Warranty
Capacity: 4.9 to 24.5 Tons
Stroke: 1" to 10"
Daylight: 20"
Shut Height: 10"
Throat: 10"
Bed Area: 24" lr x 16" fb
Ram Area: 20" lr x 10.5" fb
Speeds:
Model A:
Rapid 265 ipm
Press 130 ipm
Return 255 ipm
Model B:
Rapid 820 ipm
Press 130 ipm
Return 790 ipm
Cycles per minute: 1" stroke: 70
Cycles per minute: 4" stroke: Model A: 27 / Model B: 61
Reservoir Capacity: 60 Gallon
Motor: 15HP TEFC
Voltage: 230/460 VAC / 3ph / 60Hz
AVAILABLE OPTIONS:
Banner Zero Force Opto Touch Palm Buttons with Finger Guards
Single Stroke Automatic Circuit menu selection allows press to be cycled one
complete cycle without holding the palm buttons. Requires guarding.
FS-03 Floor Stand with adjustable leveling swivels.
LCG1 Light Curtain Guarding: Full perimeter guarding.
Front mounted light curtain guarding includes emitter, detector,
mounting hardware and installation. Fixed guarding on both sides using
wire mesh.
LVDT Programmable RAM Position Control and Digital Pressure readout.
The stroke proximity switches are replaced with a linear transducer for
ram positional control.
Operator can set, store and recall retract position, work position and
bottom stop position.
Up to 250 setups can be stored or recalled.
Pressure transducer allows system pressure readout at HMI.
Programmable Pressure Control for applications requiring dwell at force
(pricing if purchased with Option 5 programmable RAM position control)
Priority RAM Speed Control provides high resolution manual adjustment
of speed during pressing portion of stroke.
Feed Interface allows press to be interfaced with auxiliary feed system.
Requires guarding.
Dwell at Force. Includes an adjustable timer and high stability relief
which allows press to remain at force once it has achieved set pressure.
The factory recommends the use of a cooler when dwelling over 2 seconds
or when running in automatic mode
Air to Oil Cooling System with dedicated hydraulic cooling pump and
hydraulic filter.
Recommended for dwell applications over 3 sec and high cycle applications.
Foot Switch Control: Foot switch, keyed connector and quick connect.
Requires factory installed guarding.
Standard Bolster comes plain. Magnum can provide custom machining.
Просмотр других листингов такого типа
Просмотреть всеПросмотр других листингов на этот бренд
MAGNUM MCB2 GAP FRAME HYD PRESS
Гидравлические прессы
MAGNUM MCB-4A
Gap рамы (OBS) Прессы
MAGNUM HBM-15-A
Гидравлические прессы
MAGNUM HBM-25B
Гидравлические прессы