To the best of our knowledge all details listed below are deemed correct. It is the buyer's responsibility to confirm all details and we encourage an inspection of the machine(s) and accessories prior to purchase. =========================================================================== Pricing: CREST with CLWS-3-STD......... $28,500.00 CREST without CLWS-3-STD ........ $18,500.00 CLWS-3-STD Stand-a-Lone ...... $12,500.00 OC4-1014-HE - Four Stations Optimum Console (Excellent condition) Tank Dimensions: 10" l-r x 14" f-b x 10" d (8" liquid depth) Overall Dimensions: 80" l-r x 34" f-b x 39" h Process: Wash, Rinse, Rinse, Dry Chemistry: Deionized Water Automation: None Facilities: 1-3 GPM (4-6 GPM on demand) DIW@ 1-12 Mohm, 30-35 psi and process temperature, 65-70 CFM CDA @ 30 psi, 1-2 CFM shop air @ 60 psi, unrestricted floor drain. Power Requirements: 240 volts/60 Hz/3 phase. Work Flow: Left to Right. System Detail: Station #1: Ultrasonic Immersion Wash Maximum Temperature: 160 F Ultrasonic Frequency: 40 kHz Ultrasonic Power: 500 watts of ultrasonic power provided by: Six (6) transducer modules direct-bonded to the bottom of the tank. One (1) Model CG-500-40-T ultrasonic generator. Heat: 2000 watts of strip heat. Temperature control: Digital indicating temperature controller with a RTD-type temperature probe. Filtration: A 5 GPM recirculation/filtration system with: One (1) wye strainer. One (1) centrifugal, mag-drive pump, with: Ryton head. Viton o-ring. TEFC motor. One (1) 10", 10 micron cartridge filter housed in a stainless steel canister. One (1) analog pressure gauge. Manual flow control valves. One (1) recirculation returns surface sparger. Standard Features: electronic ultrasonic cycle timer. float-type low liquid level safety. capillary bulb-type overtemperature safety thermostat. basket positioner. stainless steel lift off cover. rear overflow weir plumbed to the recirculation system. Plumbing: Stainless steel compression fittings up to 1" OD. Stainless steel threaded pipe 3/4_" to 1-1/2" wherever necessary. Station #2: Ultrasonic Spray-Over-Immersion Rinse Maximum Temperature: 120 F Ultrasonic Power: 500 watts of ultrasonic power provided by: Six (6) transducer modules direct-bonded to the bottom of the tank. One (1) Model CG-500-40-T ultrasonic generator tank. One (1) Model MW 500 GTI 132 ultrasonic generator. Heat: 2000 watts of strip heat. Temperature control: Digital indicating temperature controller with a RTD-type temperature probe. Spray rinse: Stationary spray rinse package, with: One (1) set of parallel-opposed spray rinse headers that are: Fitted with removable nozzles. Located near the top of the tank. A solenoid valve on the incoming water line. The solenoid is controlled via a footswitch. Standard Features: electronic ultrasonic cycle timer. float-type low liquid level safety. capillary bulb-type overtemperature safety thermostat. basket positioner. stainless steel lift off cover. side-located overflow weir plumbed to drain. Plumbing: CPVC pipe and fitting for incoming and drain. Station #3: Spray-Over-Immersion Rinse Maximum Temperature: 120 F Ultrasonic Power: 500 watts of ultrasonic power provided by: Six (6) transducer modules direct-bonded to the bottom of the tank. One (1) Model CG-500-40-T ultrasonic generator.(optional) Heat: 2000 watts of strip heat. Temperature control: Digital indicating temperature controller with a RTD-type temperature probe. Spray rinse: Stationary spray rinse package, with: One (1) set of parallel-opposed spray rinse headers that are: Fitted with removable nozzles. Located near the top of the tank. solenoid valve on the incoming water line. The solenoid is controlled via a footswitch. Standard Features: A float-type low liquid level safety. capillary bulb-type overtemperature safety thermostat. basket positioner. stainless steel lift off cover. side-located overflow baffle with cascade flow to Station #2. Plumbing: CPVC pipe and fitting for incoming and drain Station #4: Recirculating Hot Air Dry Maximum Temperature: 180 F Heat 5000 watts of heat. Temperature control: Digital indicating temperature controller with a RTD-type temperature probe. Blower: An 1100 CFM recirculating blower in the updraft orientation. Blow-off: A stationary blow-off package, with: One (1) set of parallel-opposed air blow-off headers that are: Located near the top of the tank. solenoid valve on the incoming air line. The solenoid is controlled via a pushbutton. Cover: A manual sliding cover. Plumbing: Stainless steel tubing and fittings and brass valves. System Notes: The general system specifications are as follows: Tank Material: Type 316L stainless steel with a #2B finish Frame Material: Type 304 stainless steel support frame with leveling legs. Access Panels: Type 304 stainless steel, lift-out access panels on the sides and rear. Type 304, #4 finish, stainless steel sliding access doors on the front. Countertop: A type 304 stainless steel, removable, countertop. The countertop will be fitted with a 304 stainless steel, removable drainbacks (between the process stations). Base Plate: A type 304 stainless steel base plate. Plumbing: Complete hard plumbed process piping: Individual fill and drain connections (at the rear utility panel) will be provided for the wash station. Common fill and drain connections (at the rear utility panel) will be provided for the cascade rinse stations. All appropriate flow control and isolation ball valves. Electrical Box: Single-point electrical connection located in an end-mounted NEMA 12 enclosure. Options: Item #2: 0.3 Micron HEPA Filter including a differential pressure gauge. (Recommend maintenance replacement) Item #3: Basket: System Includes 4 ea. Model B-1014-4 Stainless Steel Work Basket. Fabricated from type 304 stainless steel. Mesh size: " (other mesh sizes available). Design to hold 30 lbs. of parts. The following option is over $20,000 new: * Model CLWS-3-STD, Closed Loop Water Conservation System, System is designed to provide DI water for final rinse of components and then recycle that water for continuous reuse. The CLWS will reduce water usage for the cleaning system by 90% while providing spot free rinse of parts being cleaned. System returns water from final rinse tank to on board gravity fed heated reservoir. Just rent the carbon and mixed bed bottles and this unit reprocesses at a 3-5 gpm rate the final rinse water. So instead of flowing 60 gallons of water down the drain the CLWS saves 90% so the system is only dumping 6-10 gallons down the sewer an hour. Capacity: 5 gpm Incoming Filter: 5 micron (from tap or RO source) Reservoir: A stainless steel holding reservoir, with liquid level controls. Heat: 15000 watts of screw-plug immersion heat. Temperature control: Includes a digital indicating temperature control. Includes an RTD-type temperature probe. Includes over-temperature safeties. Transfer pump: A centrifugal pump, with a stainless steel head and a TEFC motor. Canister: Canisters are NOT included. These canisters or bottles can be leased and serviced by your local water treatment service company such as Evoqua with two each carbon and two each mixed Ion resin exchange A resistivity monitor. Sterilizing: An ultraviolet sterilizing light. Monitors: An analog pressure gauge Outgoing Filter: 5 micron Power req's: 240 volts/60 Hz/3 phase. Console Dimensions: 80" x 34" x 38" Crest Unit: 88" x 35" x 52" 1,250 lbs Fluid Tank: 55" x 36" x 75" 475 lbs Shipping dimensions (on pallet) Crest Unit: 96" x 48" x 61" 1,500 lbs Fluid Tank: 61" x 46" x 80" 600 lbs