OC4-1014-HE - Four Stations Optimum Console Tank Dimensions: 10" left to right by 14" front to back by 10" deep (8" liquid depth). Overall Dimensions: 80" left to right by 34" front to back by 39" high. Process: Wash, Rinse, Rinse, Dry. Chemistry: Deionized Water. Facilities: 1-3 GPM (4-6 GPM on demand) DIW@ 1-2 Mohm-cm, 30-35 psi and process temperature, 65-70 CFM CDA @ 30 psi, 1-2 CFM shop air @ 60 psi, unrestricted floor drain. Power Requirements: 240 volts/60 Hz/3 phase. Work Flow: Left to Right. System Detail: Station #1: Ultrasonic Immersion Wash Maximum Temperature: 160 °F Ultrasonic Frequency: 40 kHz Ultrasonic Power: 500 watts of ultrasonic power provided by: . Six (6) transducer modules direct-bonded to the bottom of the tank. . One (1) Model 4G-500-40-T ultrasonic generator. Heat: 2000 watts of strip heat. Temperature control: Digital indicating temperature controller with a RTD-type temperature probe. Filtration: A 5 GPM recirculation/filtration system with: . One (1) wye strainer. . One (1) centrifugal, mag-drive pump, with: o Ryton head. o Viton o-ring. o TEFC motor. . One (1) 10", 10 micron cartridge filter housed in a stainless steel canister. . One (1) analog pressure gauge. . Manual flow control valves. . One (1) recirculation returns surface sparger. Include a manual bypass line control by manual ball valve. Standard Features: . An electronic ultrasonic cycle timer. . A float-type low liquid level safety. . A capillary bulb-type overtemperature safety thermostat. . A basket positioner. . A stainless steel lift off cover. . A rear overflow weir plumbed to the recirculation system. Plumbing: . Stainless steel compression fittings up to 1" OD. . Stainless steel threaded pipe ¾" to 1-1/2" wherever necessary. Station #2: Ultrasonic Spray-Over-Immersion Rinse Maximum Temperature: 120 °F Ultrasonic Frequency: 40 kHz Ultrasonic Power: 500 watts of ultrasonic power provided by: . Twelve (6) transducer modules direct-bonded to the bottom of the tank. . One (1) Model 4G-500-40-T ultrasonic generator. Heat: 2000 watts of strip heat. Temperature control: Digital indicating temperature controller with a RTD-type temperature probe. Spray rinse: Stationary spray rinse package, with: . One (1) set of parallel-opposed spray rinse headers that are: o Fitted with removable nozzles. o Located near the top of the tank. o The solenoid is controlled via a footswitch. Standard Features: . An electronic ultrasonic cycle timer. . A float-type low liquid level safety. . A capillary bulb-type overtemperature safety thermostat. . A basket positioner. . A stainless steel lift off cover. . A side-located overflow weir plumbed to drain. Plumbing: CPVC pipe and fitting for incoming and drain. Station #3: Spray-Over-Immersion Rinse Maximum Temperature: 120 °F Ultrasonic Frequency: 40 kHz . Six (6) transducer modules direct-bonded to the bottom of the tank. . One (1) Model 4G-500-40-T ultrasonic generator. Heat: 2000 watts of strip heat. Temperature control: Digital indicating temperature controller with a RTD-type temperature probe. Spray rinse: Stationary spray rinse package, with: . One (1) set of parallel-opposed spray rinse headers that are: o Fitted with removable nozzles. o Located near the top of the tank. . A solenoid valve on the incoming water line. o The solenoid is controlled via a footswitch. Standard Features: . A float-type low liquid level safety. . A capillary bulb-type overtemperature safety thermostat. . A basket positioner. . A stainless steel lift off cover. . A side-located overflow baffle with cascade flow to Station #2. Plumbing: CPVC pipe and fitting for incoming and drain Station #4: High Temperature Recirculating Hot Air Dry Maximum Temperature: 200F Heat 5000 watts of heat. Temperature control: Digital indicating temperature controller with a RTD-type temperature Blower: An 1100 CFM recirculating blower in the updraft orientation. Blow-off: A stationary blow-off package, with: . One (1) set of parallel-opposed air blow-off headers that are: o Located near the top of the tank. . A solenoid valve on the incoming air line. o The solenoid is controlled via a pushbutton. . Optional HEPA Filter Cover: A manual sliding cover. Plumbing: Stainless steel tubing and fittings and brass valves. System Notes: The general system specifications are as follows: Tank Material: Type 316L stainless steel. Frame Material: Type 304 stainless steel support frame with leveling legs. Access Panels: . Type 304 stainless steel, lift-out access panels on the sides and rear. . Type 304, stainless steel sliding access doors on the front. Countertop: A type 304 stainless steel, removable, countertop. The countertop will be fitted with a 304 stainless steel, removable drainbacks (between the process stations). Base Plate: A type 304 stainless steel base plate. Plumbing: Complete hard plumbed process piping: . Individual fill and drain connections (at the rear utility panel) will be provided for the wash station. . Common fill and drain connections (at the rear utility panel) will be provided for the cascade rinse stations. . All appropriate flow control and isolation ball valves. Electrical Box: Single-point electrical connection located in an end-mounted NEMA 12 enclosure. Shipping dimensions: 86" x 38" x 48" 1,020 lbs