Lignes de fendageSTAMCO SLITTING LINE
Etats-UnisAperçu
Marque
Modèle
Carte identité
589160
Condition
Used - Good
Année
1997
Emplacement
Etats-Unis
Numéro de stock
S-305
Manufacture
- Monarch-Stamco
- new 1997
- upgraded 2008
Material
- All common Aluminum alloys and clad products
- Full hard to dead soft temper range
Strip Width
- 24 - 62" (entry)
- 60 - 2" (exit)
Strip Thickness
- .0065 - .060"
Entry Coil Size
- ID - 16, 20, 24"
- OD - 100"
- Weight - 40,000 lbs
- Unwinding = overwind only
Exit Coil Size
- Min cut = 2”
- ID - 16, 20"
- OD - 36" max for 2-3" wide cuts / 40" max for 3-6" wide cuts / 48" max for 6-12" wide cuts / 75" max above 12" wide cuts
- Weight - 25,000 lbs max (each recoiler)
- Winding: Over and under wind capable (in any combination)
Slitter Capabilities
- Arbor Size - 6.50" diameter
- Maximum incoming width: 62”
- Minimum incoming width: 24”
- Maximum trim width: 60”
- Minimum slit width: 2”
- Cuts: .0065”-.030” (8 cuts maximum) / .031” - .060” (6 cuts maximum)
- Maximum side trim width: none as trim can be wound to winder
- Minimum side trim width: .50”
Line Speeds
- Low Gear – 500 fpm maximum
- High Gear – 1000 fpm maximum
Hand of Line
- Right to Left
Control System
- GE 90-30 PLC
Drives
- Siemens Simoreg
Line Description
- Single Uncoiler
- Dual Recoilers
- Vertical Pass Slitting
- Light/Medium Gauge aluminum
Basic Line Equipment:
- Unwind Reel Drive – 100 HP DC motor driven, dual speed gearbox
- Unwind Edge Guide: North American
- Unwind Pinch Roll
- Entry Shear
- (2) Stamco #6 Vertical Pass slitter heads (one in-line and one for next set-up;
exchange heads with overhead crane)
- Slitter Drive – 30 HP DC motor driven, single speed gearbox
- Trim Pull Rolls: Pneumatically driven
- Scrap Baller: 25 HP AC motor driven, single speed gearbox
- Recoiler Drives – 100 HP DC motor driven, dual speed gearboxes
Sold "as is, where is" EXW dismantled at plant, USA.
Photos are a combination of when the line was installed and in it's current dismantled state.
The line was properly dismantled by a rigging contractor!
Voir plus de ce modèle
TORRINGTON SLITTING LINE
Lignes de fendage
STAMCO SLITTING LINE
Lignes de fendage
SECO SLITTING LINE
Lignes de fendage
Voir plus de ce type
REUSCH
Lignes de fendage
SECO
Lignes de fendage
STAMCO
Lignes de fendage
PAXSON 72″ X .187″ X 50,000LB
Lignes de fendage
Voir plus de biens pour cette marque
STAMCO
Lignes de fendage
STAMCO 72" (1800MM) X .5" (12.7MM) X 60,000#
Lignes de fendage
STAMCO LOOPING W/ TWO INJECTOR HEADS
Lignes de fendage
STAMCO STAMCO SCRAP BALLER
Hacheur de déchets