FEATURES: * 2 1/4" SPINDLE BORE WITH D1-6 CAMLOCK SPINDLE NOSE * 7.5 HP SPINDLE MOTOR * 12 SPINDLE SPEEDS: 50 - 1800 RPM * AUTO. FEED & THREADING ARE INTERLOCKED TO PREVENT SIMULTANEOUS FUNCTIONS * HARDENED AND GROUND MEEHANITE CASTING BEDWAY * HARDENED & GROUND GEARS AND SHAFTS * THREAD CHASING DIAL & AUTOMATIC LONGITUDINAL MULTIPLE FEED STOP * CHUCK GUARD WITH SAFETY SWITCH * BUILT-IN SAFETY OVERLOAD FRICTION CLUTCH * POWER SUPPLY: 220V/3PH/60Hz SPECIFICATIONS: GENERAL CAPACITY: CENTER HEIGHT........................................ 8 1/2" SWING OVER BED....................................... 17" SWING OVER GAP (GAP TYPE ONLY)....................... 26" SWING OVER CROSS SLIDE............................... 9 5/8" DISTANCE BETWEEN CENTERS............................. 40"/60"/80" MAIN SPINDLE: SPINDLE NOSE......................................... D1-6 OR A1-6 SPINDLE BORE DIAMETER................................ 2 1/4" TYPE OF SPINDLE NOSE................................. MT #6 TAPER OF CENTER...................................... MT #4 SPINDLE SPEEDS (12 STEPS)............................ 50 - 1800 RPM CARRIAGE: CROSS SLIDE TRAVEL................................... 9 4/5" COMPOUND REST TRAVEL................................. 7" MAX. SIZE CUTTING TOOL............................... 1" X 1" TAILSTOCK: SPINDLE DIAMETER..................................... 2 1/4" SPINDLE TRAVEL....................................... 6" TAPER OF CENTER...................................... MT #4 BED: BED LENGTH........................................... 76.8"/96.1"/116.5" BED WIDTH............................................ 11 7/8" WIDTH OF GAP......................................... 8 3/4" THREADING & FEEDING: SYSTEM............................................... INCH/METRIC METRIC PITCH THREADS (22)............................ 0.5 - 7.0 MM/PITCH INCH PITCH THREADS (36).............................. 4 - 56 TPI MODULE PITCH THREADS (12)............................ 0.5 - 3.5 MP DIAMETRAL PITCH THREADS.............................. 8 - 56 DP RANGE OF LONGITUDINAL FEEDS.......................... 0.002" - 0.028"/REV .......................... 0.05 - 0.70 MM/REV RANGE OF CROSS FEEDS................................. 0.001" - 0.014" REV 0.025 - 0.35 MM/REV POWER: MAIN DRIVE MOTOR..................................... 7 1/2 HP COOLANT PUMP MOTOR................................... 1/8 HP FLOOR DIMENTIONS..................................... 85" X 40" STANDARD ACCESSORIES: 10" D1-6 3-JAW CHUCK BUILT-IN COOLANT SYSTEM 4-WAY TOOL POST FULL LENGTH SPLASH GUARD STEADY REST (0.6-7") WORK LIGHT 14" FACE PLATE GAP BED CHUCK GUARD W/ SAFETY SWITCH TOOLBOX WITH TOOLS SPECIAL PACKAGE AVAILABLE: ACER DYNAMIC "17" SERIES LATHE W/STANDARD ACCESSORIES AND "NEWALL" NMS 800 2-AXIS DRO & INSTALLED AT ACER FACILITY OPTIONAL ACCESSORIES: 8" 3-JAW CHUCK (D1-6) 10" 4-JAW INDEPENDENT CHUCK (D1-6) 12" 4-JAW INDEPENDENT CHUCK (D1-6) FOLLOW REST (BRONZE TIP): 0.78" - 4.3" RANGE 12" DRIVE PLATE "ALORIS" TOOL POST & 4-HOLDER SET (#3-BS) "ALORIS" TOOL POST & 6 HOLDER SET (#3 SET) "DORIAN" QUICK CHANGE TOOL POST & 4-HOLDER SET (SD35CXA-TS) MICROMETER STOP FOUR POSITION CARRIAGE STOP 5C COLLECT CLOSER (LEVER-TYPE) INSTALLATION FEE ON 5C COLLECT CLOSER 5C COLLECT SET (1/16" TO 1 1/16" x 16ths; 17pcs/set) TAPER TURNING ATTACHMENT INSTALLATION FEE ON TAPER TURNING ATTACHMENT "MAGNESCALE" 2-AXIS D.R.O. (10" x 40"/60"/80") "NEWALL" NMS 800 2-AXIS D.R.O. (10" x 40"/60"/80") INSTALLATION FEE ON NEWALL DP700 D.R.O. ** ABOVE PRICES ARE BASED ON F.O.B. PISCATAWAY, NJ ** PRICES AND DESIGNS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE ** MANUFACTURER RESERVES THE RIGHT TO MODIFY THE DESIGN WITHOUT NOTICE