Coe 36″ x 3/16″ x 20,000-Lb Coil Servo Feed Line Asset #16314 Consisting of: Coe CPCC-20036 Coil Cradle| Coil Staging & Loading Ramp Coe CPPS-400-36 7-Roll Coil Straightener w/ (2) Sets of Power Driven Pinch Rolls Overhead Loop Support Chute Coe 36″ Servo Feed (S/N 22189) w/ ServoMaster Control Console Coe Press Equipment Corporation AC Servo Drive Digital Rollfeed Model No. CPRF-436-PLUS Material Specifications: . Material Type: Pre-Straightened MCRS . Material Width: 36 Inches . Maximum Material Thickness: .187” x 36” Wide Performance Specifications: . Feed Angle: 180-240 Degrees . Maximum Speed: 218 Feet/Min . Acceleration: 40 Feet/Sec/Sec . Feed Accuracy: +/-.003 Inch Feed Specifications: . Number of Feed Rolls: 2 . Feed Roll O.D.: 4.00 Inches . Feed Roll I.D.: 0 Inches-Solid Rolls . Feed Roll Body Width: 18 Inches . Drive Ratio: 4.8:1 Standard Features: . Close tolerance cluster-geared upper & lower feed rolls . Air operated pilot release mechanism . Regulators for feed roll raise & lower . Crodon coated upper and lower feed rolls . AC brushless servo drive . Motor shaft encoder . Master control station (free standing) . 8 foot cable set . Jog forward and reverse . Single cycle pushbutton . Emergency stop button . Electrical safety disconnect . Remote jog with coil cord . Heavy duty cabinet base with passline adjsutable +/-5” by means of 10,000 lb. leg jacks . Entrance edge guide with self centering & independent handcrank adjustment with dual 2 ¼” diameter rolls . Material support section with funnel Standard Options: . C.P.E.C. Controller – BG-2 . Key pad length & speed input . Alpha-numeric control parameter diagnostics . 200 job memory (alpha-numeric, 8 digit) . Adjustable accel & decel rates . Footage meter . Programmable dwell for pilot release . Batch counter Item No. 2 Coe Press Equipment Corporation Free Standing Power Straightener Model No. CPPS-PO-400-36 7 Roll, 4 Inch Diameter Design Material Specifications: Maximum Coil Width: 36 Inches Maximum Stock Thickness: .187″ x 36″ Wide Payoff Rate: 90 Feet/Minute Standard Features: . Independently adjustable breaker rolls, raise and lower by means of 2 ½ ton screw jacks . Breaker roll height indicators and scales . Matte chrome finished upper and lower entrance pinch rolls . Entrance & exit cluster gear driven pinch rolls . Air operated entrance pinch rolls raise and lower with 5″ bore cylinders . Air operated exit pinch rolls raise and lower with 5″ bore cylinders . Pressure regulators for pinch roll pressure adjustment . Push button operated pneumatic control valves . Jog or automatic operation . Single operator station centrally located for the straightener and coil cradle operation . Central point grease lubrication system . 460 volt AC, 3 phase operation Standard Options: . 20 HP DC variable speed drive . Remote jog pendant with coil cord for thread up . The straightener cabinet base is to be configured with an angled top to pay off into an overhead loop tunnel out of a cradle . Entrance vertical edge guide rolls, 2 ¼” diameter with hand crank, self-centering adjustment . Ultrasonic loop control system mounted by customer above the tunnel for automatic operation . Fused electrical safety disconnect Item No. 3 Coe Press Equipment Corporation Coil Cradle Model No. CPCC-20036 Material Specifications: . Maximum Coil Weight: 20,000 lbs. . Maximum Coil Width: 36 Inches . Maximum Coil O.D.: 60 Inches . Maximum Stock Thickness: .187″ x 36″ Wide . Maximum Payoff Speed: 110 Feet/Minute Standard Features: . 5” diameter nest rolls . Hand crank independent inside plate adjustment . Air operated peeler/breaker rolls for threading . The cradle will be powered by the straightener drive . Drive is to be mounted underneath the straightener in the straightener cabinet Standard Options: . (3) side rollers in each inside plate . Air operated spare coil storage and loading ramp with hand crank adjusted side plates Feed Direction: Right to Left Voltage: 460 volt 3 phase