60" Aluminum Can-End Coating Line: CC-157 - Single coat line for light gauge aluminum coatings/finishes. - Sold "as is, where is" EXW on foundation USA. Strip Width: - 60" max / 1524 mm - 66" w/o tension leveling section Entry Coil Size: - ID - 20" (508 mm) / OD - ? / Weight - 50,000 lbs (27.2 mtons) Exit Coil Size: - ID - 16" (406 mm) / OD - 70" max (1778 mm) / Weight - 48,000 lbs (21.8 mtons) Manufacture: - Hunter and GFG - New in 1975 - Reinstalled 1984 with upgrades Design: Single coat line Line Speed: - Rated: 275 fpm / 84 mpm - Actual ran: 300 fpm / 91.4 mpm Strip Thickness: - .008 - .020" / 0.20 - 0.51mm Strip Width: - 60" max / 1524 mm - 66" w/o tension leveling section Entry Coil Size: - ID - 20" / 508mm - OD - ? - Wt. - 50,000 lbs / 11.34 mtons Exit Coil Size: - ID - 16" / 406mm - OD - 70" max / 1778mm - Wt - 48,000 lbs / 10.89 mtons Uncoiler #1: - 80 hp, 800/1500 rpm, 15.983:1 gear ratio Coil Car #1: - Above ground, 50,000 lbs Scrap Winder: - Mandrel type with scrap car Uncoiler #2: - 80 hp, 800/1500 rpm, 15.983:1 gear ratio Coil Car #2 - Above ground, 50,000 lbs Pinch Roll Crop Shear Strip Joiner: - Behlen, Single die Bridle 1 of 7 Entry Accumulator: - 9 rolls over 8 - 12.8" diam rolls - 60 seconds of strip storage at 300 fpm Bridle 2 of 7 Tension Leveler: - 60" max strip width - Entry Bridle (Line bridle #3)(2 roll unit) - Roll 1 - 25 hp, 1750/2500 rpm, 34.13:1 gear ratio - Roll 2 - 50 hp, 1750/2500 rpm, 33.23:1 ratio - BWG Flex-Roll Section: - 5 roll cassettes - Work rolls: 1.125" & 1.75" diam - Back up Rolls: 2.25" diam - Exit Bridle (Line bridle #4)(2 roll unit) - Roll 3 - 150 hp, 1750/2500 rpm, 34.5:1 gear ratio - Roll 4 - 75 hp, 1750/2500 rpm, 33.02:1 gear ratio Bridle 5 of 7 Cleaning Section - Stages 1-2 = vertical - Stages 3-4-5 = horizontal - Vertical Air blow off Coater: - GFG, 2 side coat - Rolls: 10" diam x 72" face Paint Flow-Out Booth - 15 ft long section Oven: - 90 ft long / 27.4 m - 3-zone gas-fired catenary type - Exit water quench - Exit air quench Bridle 6 of 7 Exit Accumulator: - 9 rolls over 8 - 12.8" roll diameter - 60 seconds of strip storage at 300 fpm Bridle 7 of 7 Waxer: - GFG - 2-12 mg per sq ft laydown Exit Shear Exit Pinch Roll Recoiler: - 60 hp, 500/2000 rpm, 18.611:1 gear ratio - Mandrel type - With Belt wrapper, coil car, and downender